Journal Bearing Failure Analysis: Causes, Signs and Prevention

Journal Bearing Failure Analysis

Table of Contents

Journal bearing failure analysis is the process of finding out why a hydrodynamic bearing failed. You match the damage on the babbitt lining to a failure mode, confirm it against operating history, oil analysis, clearance and alignment, then correct the root cause. Done well, it stops the replacement bearing from failing the same way.

Most journal bearing failures start outside the bearing. Oil supply, dirt, alignment, load and stray current do the damage, and the soft babbitt records it. That’s why the lining is the best evidence you have, and why swapping the shell without reading it rarely solves anything.

Journal bearing failure analysis chart matching babbitt damage signs to their likely causes

What Causes Journal Bearing Failure?

A journal bearing has no balls or rollers. The rotating shaft pulls oil into a wedge-shaped gap and builds enough pressure to float on it. Machine Design puts that film at roughly 0.0004 to 0.004 in. thick, thinner than a sheet of paper.

This is the main difference from rolling element bearings, which carry load through steel contact. A journal bearing only survives while the film does. Five conditions break the film in most cases.

Oil starvation. Low pressure, a clogged supply hole, a failed pump or a sluggish oil ring on a cold start leaves too little oil to build pressure. The journal touches the babbitt within seconds.

Contamination. Particles larger than the film thickness cut grooves as they pass through the load zone. Water and salt are worse than they look: saltwater can grow a hard tin oxide layer on tin babbitt up to 100 µm thick, which later breaks off and acts as an abrasive.

Wrong clearance. A tight journal bearing restricts oil flow, so heat builds faster than the oil can carry it away. A loose bearing loses film stiffness and damping, and vibration climbs. Clearance also drifts open over the years as worn shells get scraped and refitted.

Misalignment. When the shaft sits at an angle, one edge of the shell carries most of the load. Some misalignment only appears hot, after the pedestal grows or tilts. Plain journal bearings tolerate very little of it, unlike spherical plain bearings, which are designed to let the shaft tilt.

Overload. Static overload, rotor unbalance and vibration all push peak film pressure past what the babbitt can carry. Start and stop are the riskiest moments, because the film hasn’t formed yet. Machine Design notes that radial loads of 400 psi or more are prone to wiping during starts and stops unless the machine has jacking oil to lift the shaft. Axial overload causes the same problems in the companion thrust bearings.

What Does Journal Bearing Damage Look Like?

Each cause leaves its own fingerprint on a journal bearing. Where the damage sits matters as much as what it looks like, so note its position across the width and around the circumference before you clean anything.

Scoring. Fine circumferential grooves, heaviest in the load zone at the bottom of the shell. Typical grooves run 0.001 to 0.040 in. wide and deep. Scoring points to hard particles in the oil, or a scored journal running against new babbitt.

Wiping. Smeared, melted babbitt pushed from the contact point toward areas with more clearance. It means the film broke down and metal touched metal. Wiping across the full width suggests starvation or overload. Wiping on one edge points to misalignment. Wiping at the very bottom of a large bearing suggests long slow rolling on turning gear without enough lift oil.

Journal bearing wiping patterns: full-width, one-edge and bottom-center wiping with likely causes

Fatigue cracks. A crack network on the surface, sometimes with pieces of babbitt missing. Cracks start at the surface and grow toward the bond with the steel backing. Cyclic load from vibration or unbalance is the usual driver, and heat speeds it up because the babbitt loses fatigue strength as it gets hotter.

Discoloration. Dark, lacquer-like varnish in the hottest zones means the oil is breaking down from age or heat. Blue or straw heat tint on the steel journal means severe overheating, often just before seizure.

Corrosion and pitting. Small angular pits come from acids in aged oil attacking the alloy. Rounded pits with a frosted, matte look are electrical pitting, caused by stray current arcing through the thinnest part of the film. The two look similar at a glance, but the fix is completely different.

Journal Bearing Failure Analysis Chart

Use this chart as a starting point. Confirm every cause with at least one check before you act on it.

Damage signLikely causeWhat to checkCorrective action
Circumferential grooves in load zone (scoring)Contaminated oil, scored journalParticle count, filter condition, journal surface finishUpgrade filtration, flush system, polish or replace journal
Smeared babbitt across full width (wiping)Oil starvation, tight clearance, overloadOil pressure and flow, measured clearance, start/stop recordsRestore oil supply, correct clearance, add or repair jacking oil
Wiping or polishing on one edgeMisalignmentCold and hot alignment, pedestal growth, soft footRealign for operating temperature
Crack network, missing babbitt (fatigue)Cyclic load, vibration, high temperatureVibration trend, rotor balance, babbitt temperatureBalance rotor, reduce vibration, review babbitt thickness
Varnish or heat tintOverheating, oil breakdownOil inlet temperature, oil age, cooler performanceChange oil, restore cooling, recheck clearance
Rounded frosted pitsStray electrical currentShaft voltage, grounding brush, pedestal insulationRepair shaft grounding, insulate the pedestal
Angular pits or hard grey depositsCorrosion, water or salt in oilWater content, acid number, seal conditionStop water ingress, change oil
Fretting on shell back or joint facesLoose housing fit, low crushHousing bore, bearing crush, dowelsRestore correct fit and crush

How Do You Diagnose a Failed Journal Bearing?

A good journal bearing failure analysis follows the same five steps every time. Skipping one is how teams end up blaming the bearing for a lube system problem.

Five-step journal bearing failure analysis process from operating history to alignment check
  1. Review operating history. Pull bearing temperature, vibration and oil pressure trends for the weeks before the failure, plus any trips, overspeeds or unusual starts. A sudden temperature spike is often the first sign of a wipe, even when it never crosses the alarm setpoint.
  2. Inspect the surfaces. Photograph both halves in place, then map the damage by position. Inspect the journal as well. A scored, tapered or out-of-round shaft reduces load capacity as much as a worn lining.
  3. Test the oil. Send a sample and the used filter element to a lab. For tin babbitt, rising tin, antimony and copper show the lining is wearing. Ask for particle count, water content and acid number too, because those point to the cause rather than the result.
  4. Measure clearance. Compare the measured clearance with the drawing. Check the housing fit and bearing crush at the same time.
  5. Check alignment. Measure cold and, where possible, at operating temperature. Look for fretting on the shell back, joint faces and dowels, which signals movement or distortion.

Write down the evidence for each possible cause. If two causes fit, act on the one that changes your fix first.

Should You Repair or Replace the Bearing?

Ask one question: will this journal bearing carry its full expected load, including starts and stops, if it goes back in?

Journal bearing repair or replace criteria: when to reuse and when to rebabbitt

A journal bearing can usually be cleaned and reused when:

  • Damage is limited to light polishing or minor wiping
  • Clearance is within drawing limits
  • Oil grooves and supply holes are clear
  • There are no cracks and the bond is sound

Replace it, or send it for rebabbitting, when any of these apply:

  • Clearance is outside limits
  • Fatigue cracks or missing babbitt appear in the load zone
  • Deep scoring crosses the load zone
  • Wiped metal has blocked an oil groove
  • The babbitt has lifted or debonded from the steel shell

Bond failure and fine cracks are often invisible. Ultrasonic testing checks the bond, and dye penetrant reveals surface cracks, both covered under ISO 4386. Bring in a bearing repair specialist when you lack that equipment, when damage sits close to the limits, or when the bearing supports a critical machine such as a steam or gas turbine in power generation. For pumps, fans and compressors in general industrial machinery, the same criteria apply, but in-house repair is often practical.

How Can You Prevent Repeat Failures?

Start with the root cause your journal bearing failure analysis found. Then lock in the basics so nothing else takes its place.

Correct lubrication. Use the specified oil grade and viscosity, keep inlet temperature stable and confirm pressure and flow at every bearing, not just at the pump. Change oil before it starts to varnish. On machines that see seawater or wash-down, such as marine equipment, check water content on every oil report.

Filtration. Choose filters that stop particles larger than the minimum film thickness. Flush any new or rebuilt system thoroughly, then drain and refill the oil after the first couple of weeks to remove leftover assembly debris.

Installation. Clean every part with the oil you’ll run on. Measure clearance, housing fit and crush. Align with thermal growth in mind. Never fit a new shell on a scored journal without polishing or replacing it.

Condition monitoring. Trend bearing metal temperature against the machine’s own baseline instead of a generic limit, and alarm on sudden rises as well as high levels. On larger machines, two proximity probes 90° apart track shaft position and orbit. A centerline drifting lower over months means wear. Vibration near half running speed suggests oil whirl.

Standard vibration analysis built for rolling bearings won’t catch most journal bearing faults, because there are no balls or rollers to create defect frequencies. Wind turbine gearboxes show the contrast well: gearbox bearing failure signs differ sharply between rolling and journal designs.

Electrical protection. Keep shaft grounding brushes in service and check pedestal insulation during outages. Where the motor or generator runs on rolling bearings instead, electrically insulated bearings block the same stray current path.

Frequently Asked Questions

What causes wiping in a journal bearing?

Wiping happens when the oil film collapses and the journal touches the babbitt, heating the surface until it smears. The usual triggers are oil starvation, tight clearance, misalignment, overload and heavy loads during starts and stops.

How does oil starvation damage bearings?

Without enough oil, the journal bearing can’t build film pressure, so the shaft rubs the lining. Friction heats the babbitt within seconds, causing wiping and then seizure if the supply isn’t restored. Displaced babbitt can also block oil grooves and make the starvation worse.

Can a damaged journal bearing be reused?

Sometimes. Light polishing or minor wiping can be cleaned and reused if clearance is within limits, oil grooves are clear and the bond is sound. A detailed survey of babbitted bearing damage in Lubricants explains that limited wiping often leaves a workable surface, while cracks, bond loss and deep scoring reduce load capacity.

Who can help with a journal bearing replacement or a switch to rolling bearings?

If you’re replacing bearings on a critical machine or reviewing whether a rolling bearing design suits your application, contact the TFL engineering team with your drawings, part numbers and operating conditions.

Tags

Welcome To Share This Page:

Product Categories
Get A Free Quote
Related News

Shaft Bearing Guide: Types, Arrangements and the Right Fit

You have a rotating shaft, two bearing seats and a drawing that says “k5.” That’s the usual starting point for anyone looking up shaft bearings. A shaft bearing is any bearing that supports a turning shaft and keeps it in place, either a plain bearing (the shaft runs in a lined hole) or a rolling […]

Linear Motion Bearing Guide: Types, Life Math and How to Choose

Compare linear ball bushings, profiled rail guides and plain linear bearings, calculate L10 life in km with an LM12UU example, and choose the right type.

L44649 Bearing: Dimensions, Load Ratings and How to Identify It

The L44649 bearing is an inch-size tapered roller cone with a 1.0625 inch (26.988 mm) bore. It pairs with the L44610 cup, which has a 1.9800 inch (50.292 mm) outside diameter, and together they make the L44649/L44610 set. You’ll find it most often in trailer wheel hubs on 1-1/16 inch spindles, and in general automotive […]

Bearing Race: What It Is, Types, Materials and Damage Signs

What a bearing race is, inner vs outer race differences, raceway shapes by bearing type, race steels, and how to read spalling, brinelling and other race damage.

Babbitt Bearing: 5 Grades, Types & Best Care

A babbitt bearing is a plain bearing whose sliding surface is lined with babbitt metal, a soft white metal alloy based on tin or lead. During normal running the shaft journal doesn’t touch that metal at all. It floats on a thin film of oil, and the babbitt lining is there to protect the shaft […]

Cam Follower: Types, Working Principle, Applications & Selection Guide

A cam follower is a roller bearing with a thick outer ring that rolls directly on a cam, track or rail. Most use needle rollers inside, and many have a threaded stud in place of an inner ring, so you mount one with a single hole and a nut. That thick outer ring is what […]

Linear Guide Rail: Types, Uses and Sizing

How a linear guide rail works, ball vs roller vs miniature types, and a 6 step method to size one with load, L10 life, accuracy grade and preload.

Active Magnetic Bearings: A Simple Guide for Buyers and Engineers

Active magnetic bearings (AMBs) hold a spinning shaft in the air with electromagnets. The shaft never touches the bearing. Sensors watch where the shaft is, and a small computer changes the magnet power to keep it in the center. Because nothing touches, there is no oil, almost no friction and very little wear. That makes […]

Hybrid Ceramic Bearings: Benefits, Uses, Sizes and How to Choose

Hybrid ceramic bearings are rolling bearings with steel inner and outer rings and balls (or rollers) made of silicon nitride (Si3N4) ceramic. They spin faster, run cooler, last longer with poor lubrication and stop electric current from passing through the bearing. They cost more than steel bearings and carry less static load. Use hybrid ceramic […]

NU205 Bearing Dimensions: Full Size Chart, Load Ratings and Specs

NU205 bearing dimensions are 25x52x15 mm. See the size chart, load ratings by brand, NU205 vs NJ205 differences and measuring tips.

22220 Bearing Dimensions: Size Chart, Load Ratings and C3 Clearance

22220 bearing dimensions are 100 x 180 x 46 mm. See the size chart, load ratings by suffix, C3 clearance and SKF, FAG, NSK and Timken equivalents.

6205 Bearing Dimensions: Size Chart, Specs and Variants in mm and Inches

The 6205 bearing dimensions are 25 mm inner diameter, 52 mm outer diameter and 15 mm width, usually written as 25x52x15. In inches, that’s about 0.984 x 2.047 x 0.591 in. Every 6205 shares this size, whether it’s open, 2RS, ZZ or C3. That’s the quick answer. But the letters after “6205” change speed, sealing […]

Square Linear Bearing: Types, Codes, Uses and How to Choose

A square linear bearing is a linear motion bearing with a square bore, a square flange or a square housing, so it bolts flat to a machine and slides in a straight line. The name covers three different parts. Pick the wrong one and it simply won’t fit your shaft. Here’s the quick answer. Need […]

608 Bearing Dimensions: Easy Size Chart in mm and Inches (2026)

The standard 608 bearing dimensions are an 8 mm inner diameter, a 22 mm outer diameter and a 7 mm width, written as 8x22x7 mm. In inches, the 608 bearing size is about 0.315 x 0.866 x 0.276. These numbers stay the same whether the bearing is open, 608ZZ or 608 2RS. The 608 is […]

Female Rod End Bearing: Sizes and Threads

A female rod end bearing is a rod end with an internal thread in its shank, so it screws onto a threaded rod or cylinder piston rod instead of into a tapped hole. Inside the eye sits a spherical plain bearing: a ball with a bore that swivels in the housing, letting the linkage run […]

Cast Iron Bearing Housing: Types, Sizes and How to Choose One

One SKF plummer block datasheet lists a breaking load of 210 kN when the load pushes straight down into the base. Swing that same load to 150 degrees, so it pulls toward the cap, and the figure falls to 120 kN. Same cast iron bearing housing, same bolts, roughly 43% less strength. That gap explains […]

How hot is too hot for a bearing article hero image with overheated bearing visual
Bearing Maintenance
Jessica Jia

How Hot Is Too Hot for a Bearing?

Learn why bearing overheating has no universal temperature limit, how to read temperature trends, and when a hot bearing needs investigation or shutdown.

Read More »
About TFL Bearings

Why is TFL BEARINGS frequently chosen as the specified bearing brand by major international companies?

Reliable Operation Starts Here

Contact TFL Bearings for the Best Solutions!

Our efficient global supply chain and inventory management ensure fast response and timely delivery.

We tailor bearing solutions to unique needs. Services include design advice & custom specifications for your specific application.

Competitive prices. Quality bearings meet int'l stds; interchangeable. Reliable, economical alternative. Lower costs, keep performance & value.

Quality products plus reliable full service. Our pro team offers support from selection to after-sales. We aim to be your trusted partner.