The L44649 bearing is an inch-size tapered roller cone with a 1.0625 inch (26.988 mm) bore. It pairs with the L44610 cup, which has a 1.9800 inch (50.292 mm) outside diameter, and together they make the L44649/L44610 set. You’ll find it most often in trailer wheel hubs on 1-1/16 inch spindles, and in general automotive and industrial equipment.
Below you’ll find the full dimensions, why the load ratings look different from one catalog to the next, and how to make sure the part in your hand really is an L44649 bearing before you order. It belongs to the wider family of tapered roller bearings, which share the same cone and cup design.
L44649 bearing dimensions
The L44649 bearing is only the cone: the inner ring, rollers and cage. The cup (outer ring) is a separate part, the L44610. You can also order the L44649 single cone on its own. If you’re new to the cone and cup terms, our guide to the bearing race explains how the two halves work together.
| Dimension | Inch | Metric |
|---|---|---|
| Cone bore (d) | 1.0625 in | 26.988 mm |
| Cup outside diameter (D) | 1.9800 in | 50.292 mm |
| Cone width (B) | 0.5800 in | 14.732 mm |
| Cup width (C) | 0.4200 in | 10.668 mm |
| Set width (T) | 0.5600 in | 14.224 mm |
| Set weight | 0.265 lb | 0.120 kg |
Figures come from the Timken and NTN catalog pages for the L44649/L44610 set. Timken lists the cage as stamped steel and the series as L44600. NTN rates its version at ABMA Class 2 precision, with an operating range of -40 to 250 °F.

L44649 bearing load ratings: why the numbers don’t match
Compare two catalogs and you’ll see different load ratings for the same part number. That confuses a lot of buyers, and it usually comes down to how each maker states the rating.
| Rating | Timken L44649/L44610 | NTN L44649/L44610 |
|---|---|---|
| Dynamic radial, 1 million revolutions (C1) | 6,760 lbf (30.1 kN) | 6,450 lbf (28.8 kN) |
| Dynamic radial, 90 million revolutions (C90) | 1,750 lbf (7.79 kN) | Not listed |
| Static radial (C0) | 7,400 lbf (32.9 kN) | 7,650 lbf (34.0 kN) |
| Dynamic thrust, 90 million revolutions (Ca90) | 1,120 lbf (4.99 kN) | Not listed |
Timken publishes two dynamic ratings. The C1 figure uses the ISO basis of 1 million revolutions, while the C90 figure is based on 90 million revolutions. The C90 number looks almost four times smaller, but it describes the same bearing on a different life basis.
So when you compare quotes, check that both suppliers state the rating on the same basis. A quote listing “1,750 lbf” and another listing “6,760 lbf” can describe the very same L44649/L44610 set. Our bearing failure analysis services guide covers what to check when a bearing fails well short of its rated life.
The small gap between Timken and NTN (30.1 kN against 28.8 kN on the same basis) is normal. Each maker uses its own roller profile and steel, so ratings rarely match to the decimal.
Where the L44649 bearing is used
Trailer hubs are the big one. etrailer lists the L44649 bearing for 3,500 lb trailer axles, used as both the inner and outer bearing on a BTR spindle, or as the outer bearing on a #84 spindle. In that second setup the inner bearing is a different part, so don’t assume both bearings in a hub are the same.

A tapered roller bearing like this one carries radial load plus thrust in one direction, which suits a wheel hub where cornering pushes the wheel sideways. That’s why hubs use two cones facing opposite ways.
Bearing dealers also list it for caravan axles and general automotive and industrial use. Timken also builds a two-row L44649 assembly (L44649-90044) with an overall width of 1.245 inches for heavier positions. See our automotive bearings page for the other bearing types we supply for vehicles.
How to confirm you have an L44649 bearing
Part numbers wear off, and a worn stamp is an easy way to order the wrong bearing. One etrailer customer asked about an “L44949,” a number the experts couldn’t find. Their advice was to measure the bore, because the stamping was probably worn.
Do this before you order:
- Clean the cone and read the stamp on the large face. Look for L44649, and for the cup, L44610.
- Measure the bore with a digital caliper. An L44649 bearing reads 1.0625 inch, or about 26.99 mm.
- Measure the cup’s outside diameter. The L44610 reads 1.9800 inch (50.29 mm).
- Check the cup width: 0.4200 inch (10.67 mm).
If your bore reads exactly 1.000 inch (25.4 mm), you likely have an L44643 instead. Timken lists the L44643 with the same L44610 cup, the same 1.98 inch OD and the same width, so the two sets look identical from the outside. Only the bore gives it away.
When the stamp is gone and the caliper reads something else, our bearing cross reference page helps match the dimensions to a standard number.
Replacing an L44649 bearing: buy the cup too
Replace the cone and cup together. The rollers and the cup raceway wear against each other, so a new cone in an old cup starts life on a worn track. Trailer parts sellers usually list the L44649 bearing with its L44610 race for that reason, and you can order the matched L44649/L44610 set from us the same way.
Check the grease seal at the same time, because a torn seal lets water and grit into the hub. If you hear grinding or humming from a hub, our guide to wheel bearing noise explains how to tell which bearing is failing.
Common L44649 bearing equivalents
The L44649 number is standard across the major brands, so the cone interchanges directly:
| Brand | Cone | Cup | Set |
|---|---|---|---|
| Timken | L44649 | L44610 | L44649/L44610 |
| NTN | 4T-L44649 | 4T-L44610 | 4T-L44649/L44610 |
| SKF | L 44649 | L 44610 | L 44649/610 |
| SNR | L44649 | L44610 | L44649/610 |
NTN adds a “4T” prefix and SKF writes the number with a space, but the dimensions are the same. Always check the full set number on the box, since some suppliers bundle the cone and cup and others sell them apart. You can see how we inspect bearings before shipping on our quality and capabilities page.
For other inch and metric sizes, browse our single row tapered roller bearings.
Quick answers
What size is an L44649 bearing?
1.0625 inch (26.988 mm) bore, 0.5800 inch (14.732 mm) cone width. With the L44610 cup, the set is 1.9800 inch (50.292 mm) OD and 0.5600 inch (14.224 mm) wide.
What race goes with an L44649 bearing?
The L44610 cup. It also fits the L44643 cone, which has a 1 inch bore.
What trailer axle uses the L44649 bearing?
Commonly 3,500 lb axles with 1-1/16 inch spindles, either as both bearings on a BTR spindle or as the outer bearing on a #84 spindle.
Can I buy L44649 bearings in bulk?
Yes. Send us the set number and quantity through our contact page, and we’ll confirm the brand options, MOQ and lead time for your order.

